Dev board
ESP32-C3 SuperMini
A 22.5 × 18 mm board around the ESP32-C3: a single RISC-V core, Wi-Fi and Bluetooth LE, 4 MB of flash in the chip, and USB-C wired straight to the chip’s own USB. It’s cheap and small, and its defaults hide a few traps: Arduino puts I²C on two strapping pins, the USB port vanishes when your code sleeps, and many boards won’t hold a Wi-Fi connection at full power.
Specs
| Chip | ESP32-C3FN4: ESP32-C3 with 4 MB flash in the package |
|---|---|
| CPU | 32-bit RISC-V, single core, up to 160 MHz |
| Memory | 400 KB SRAM, 384 KB ROM, 4 MB flash |
| Radio | 2.4 GHz Wi-Fi 802.11 b/g/n, Bluetooth 5 (LE) |
| Header | 16 pins: 13 GPIOs (IO0–IO10, IO20, IO21), 5V, 3V3, GND |
| Analog | 12-bit ADC1 on IO0–IO4. IO5 is ADC2, which can’t be read |
| USB | USB-C to the C3’s USB Serial/JTAG (GPIO18/19). No USB-to-UART chip |
| Logic level | 3.3 V. Inputs take at most 3.6 V |
| Power in | USB-C, or 3.3–6 V on the 5V pin, or 3.3 V on the 3V3 pin. One at a time |
| On board | BOOT button (IO9), RESET button, blue LED (IO8, active low), red power LED |
| Size | 22.52 × 18 mm, parts on one side |
| Deep sleep | About 43 µA (vendor figure) |
Pins
| Pin | Roles | What to know |
|---|---|---|
| 5V | Power | USB 5 V out when on USB. Or power the board here, without USB plugged in. |
| GND | Ground | Shared with every module. |
| 3V3 | Power | The board’s 3.3 V rail. Power sensors from here. |
| IO4 | ADC1_CH4SCK | Free to use. |
| IO3 | ADC1_CH3A3 | Free to use. |
| IO2 | ADC1_CH2A2 | Strapping pin. Keep it high at reset. |
| IO1 | ADC1_CH1A1 | Free to use. |
| IO0 | ADC1_CH0A0 | Free to use. |
| IO5 | ADC2_CH0A5MISO | Digital only: ADC2 reads aren’t supported on the C3. |
| IO6 | MOSI | Free to use. |
| IO7 | SS | Free to use. |
| IO8 | LEDSDA | Strapping pin, must be high to flash. Drives the onboard LED. |
| IO9 | BOOTSCL | Strapping pin: low at reset means download mode. |
| IO10 | – | Free to use. |
| IO20 | RX | UART0 receive. Free when you don’t use the UART. |
| IO21 | TX | UART0 transmit. Carries the boot log at every reset. |
Rows in bold need care. Roles after the ADC channel are the Arduino core’s defaults for this board (A0–A5, SPI, I²C, Serial1). Every pin can be remapped in code.
Powering it
There are three ways in: USB-C, a supply on the 5V pin (the vendor gives 3.3–6 V), or a regulated 3.3 V on the 3V3 pin. The board has no circuit that switches between them, so use one at a time. Don’t leave a 5 V supply on the 5V pin while USB-C is plugged in to flash it.
The 5V pin is only 5 V when USB or a 5 V supply feeds it. Anything you power from it can put 5 V on a GPIO through its output or its pull-ups, and a C3 input takes at most 3.6 V. Power sensors from 3V3 unless they have their own regulator and level shifting.
Uploading over USB-C
There is no USB-to-serial chip. USB-C goes to the C3’s built-in USB Serial/JTAG on GPIO18 and GPIO19, which aren’t on the header. Two things follow from that.
In the Arduino IDE, set USB CDC On Boot to Enabled, or Serial.print goes to the
UART on IO21 instead of the USB port, and the serial monitor stays empty.
The USB port exists only while the chip runs code that keeps it alive. It drops out when your sketch enters deep sleep or reconfigures GPIO18 or GPIO19. Then the port disappears and uploads fail. To get it back:
- Hold BOOT.
- Press and release RESET.
- Release BOOT. The board is now in download mode and the port is back.
- Upload, then press RESET to start the new sketch.
This works because BOOT pulls IO9 low at reset, which is the ROM’s download mode. It’s also why nothing on your circuit should hold IO9 low at reset: the board would boot into download mode every time.
Arduino’s default pins
If you call Wire.begin() without pins, the Arduino core puts I²C on IO8 (SDA) and
IO9 (SCL). Both are strapping pins, IO8 drives the onboard LED and IO9 is the BOOT button.
It works, since I²C idles high with its pull-ups, but the LED flickers with bus traffic and
pressing BOOT pulls SCL low. Free pins avoid all of that:
Wire.begin(6, 7); // SDA, SCL
The default SPI pins are IO4 (SCK), IO5 (MISO), IO6 (MOSI) and IO7 (SS), all fine for SPI. Analog pins A0 to A5 map to IO0 to IO5, but A5 (IO5) is on ADC2, which the C3 can’t read. Use A0 to A4.
When Wi-Fi won’t connect
A common SuperMini complaint: the board won’t join a network, or drops the connection, at the default transmit power. The fix people report most often is to lower it right after starting Wi-Fi:
WiFi.begin(ssid, password);
WiFi.setTxPower(WIFI_POWER_8_5dBm);
Range gets shorter, but the connection holds. The suspected cause is layout: on many boards the chip antenna sits right next to the crystal, and boards with more space between the two are reported to do better. Keep wires and metal away from the antenna end of the board too.
On the board
- BOOT connects IO9 to GND. Pressing it while your code runs pulls IO9 low, so a signal on IO9 sees that.
- RESET restarts the chip.
- The blue LED is on IO8 and lights when IO8 is low.
- The red LED is on whenever the board has power.
Sources
- ESP32-C3 datasheet v2.4: CPU, memory, radio, ADC, strapping pins, input voltage.
- nologo.tech ESP32-C3 SuperMini wiki: Chip variant, size, 5V pin input range, deep sleep current, LED, buttons, download mode steps, USB CDC On Boot.
- Arduino core for ESP32, nologo_esp32c3_super_mini variant: Default pins: SDA 8, SCL 9, SPI 4–7, A0–A5, TX 21, RX 20, LED_BUILTIN 8.
- ESP-IDF: USB Serial/JTAG console: USB disconnects in deep sleep and when GPIO18/19 are reconfigured; recovery through GPIO9.
- Protosupplies ESP32-C3 SuperMini: No power switching between USB, 5V and 3V3; red power LED; antenna-to-crystal spacing on some boards.
- mikrocontroller.net: Esp32-C3 Super Mini, keine WLan-Verbindung: Boards that only connect with TX power lowered to 8.5 dBm.
Boardless checks your wiring against parts like this
I’m building Boardless to check your schematic, case and firmware against each other on every change. Each part page is what it knows about that part.
You're on the list.
Got a minute? Tell me which boards you use and I'll know what to support first.